| 
PB6000
G6060
G6070
G6070P
Drive
System
Double 120 roller chain to drive the rotor - PB6000, G6060 &
G6070 models
Large planetary gear box to drive the rotor on the G6070P model
Heavy duty PTO shaft with shear protection
Power requirements on the PB6000, G6060 & G6070 models only
need a maximum of 120 HP!
The horsepower requirements on the G6070P planetary drive model
is only a maximum of 120 HP but can take up to 150 HP!
Self-Contained
Hydraulic System
The G6060, G6070 & G6070P model baggers are equipped
with a self-contained hydraulic system that runs off the dual output
gear box.
The
self-contained hydraulic system allows you to operate:
The variable speed feed conveyor from ground level
Does not create heat in the tractor hydraulic system and allows
the use of older vintage tractors with low volume hydraulics
Operate the optional variable speed cable rewind system
Operate the optional hydraulic conveyor slide system
Bag
Boom & Bag Cradle
All models are available with a bag boom and bag
cradle.
Makes installing the Ag-Bag bag quick and easy
Aids in installing different tunnel sizes and/or tunnel extensions
Can be used to place the back stop onto the transport braces
Tunnels
& Tunnel Extensions
PB6000 bagger can be ordered with either an 8' or
9' one piece tunnel
G6060 bagger can be ordered with interchangeable 8' or 9' tunnels
- 8' x 24" and/or 9' x 24" tunnel extensions are optional
G6070 & G6070P baggers can be ordered with interchangeable 9'
or 10' tunnels - 24" tunnel extensions are standard with the 9'
or 10' tunnels
Tunnel extensions increase bag capacity by packing silage tighter.
They also create a smoother bag. |
|
Frames
The main frame is the foundation of any bagger and it is critical
that the frame stay rigid to keep the rotor running true. The
Ag-Bag 6000 series frames are made out of heavy wall structural
steel tubing and heavy gauge flat plate throughout to create a
solid foundation to an exceptional bagger.
Rotor
Design
The rotor and tunnel design are the key to a well packed bag. Ag-Bag
started in 1978 and was  the
first company in the United States to build bagging machines. Ag-Bag
wrote the book on where the rotor needed to be placed, how wide
it had to be to for a given tunnel size, how many teeth the rotor
needed and where they had to be positioned.
Low
rotor position provides consistent packing through the entire
bag
Large
footed rotor bearings with remote grease line
Model |
Drive
Side |
PB6000
& G6060 |
2-15/16" |
G6070 |
3-7/16" |
G6070P |
Planetary
reduction gear box |
 Replaceable
wear strips on teeth
Conveyor(s)
Straight conveyors for baggers with 6' rotors (PB6000
& G6060)
Split conveyors for baggers with 7' rotors (G6070 & G6070P,
optional on G6060)
30" wide conveyor for high capacity
Lower clean out door for long life
CA550 roller chain for smooth
operation and long life (top driven)
Conveyor moves with a cable and winch, hydraulic slide optional
Cable,
Cable Drum Brake(s) & Back Stop
The dual cable system allows you to make a well compacted
bag with ease. Large industrial disc brake(s) and a simple brake
hand pump and brake pressure gauge control the rate of cable release.
Ag-Bag bags have convenient
stretch gauges continually along the bag to insure consistency.
The bag back stop is a heavy duty steel frame webbed with rope to
insure no damage to the bag. An optional lightweight aluminum back
stop is also available for the G6060 and G6070 baggers.
Transport
Transport lights, slow moving vehicle sign and reflective tape are
used to mark the bagger for transport
The G6060, G6070 & G6070P can be narrowed to an 8-1/2' transport
width
Inoculant
Package
To insure top quality feed Ag-Bag recommends the
use of specially formulated Ag-Bag Inoculants. Both liquid and granular
inoculants along with applicators are available to help insure top
quality feed.
|
